PCWorld Forums

PCWorld Forums: C P U Fan Died - PCWorld Forums

Jump to content

PCWorld Community

Help

Page 1 of 1

You cannot start a new topic
You cannot reply to this topic

C P U Fan Died R.I.P. C P U fan

#1 snorg

Expert

Group: Members
Posts: 2,911
Joined: 28-November 07
Location:In the wild

Posted 26 November 2012 - 03:27 AM

I bought 2 of these fans for push/pull on my CPU cooler, they are 110cfm and only 10 bucks.
One died in a month, the other died today at about 6 months.
Do Not buy this fan.
Scythe Slip Stream Kaze Jyuni 120MM Fan 1900RPM 110.3CFM 37DBA
manufactures Part #: SY1225SL12SH

I have ordered this fan, should be here in 5 days.
Silverstone 120MM FM121 Case Fan 800-2500RPM 17-39.5DBA MAX. 110CFM W/ Black Knob
manufactures Part #: RL-FM121-B
Its 110cfm, 2 ball bearings, 12 bucks, hopefully it will last along time.

Meanwhile I under clocked CPU to 2GHz, it was overclocked to 4GHz, so this will keep CPU from getting to hot for now. Its about 58c rite now under little load.

Asus Vento Mini Tower Case....Asus M5A87 MOBO.....AMD Phenom II X6 1100T ( 3.3 OCed to 4.1GHz ).... Coolermaster Hyper 212 Evo.... Three Seagate Barracuda 1TB SATA III.... 8GB Corsair Vengeance Blue 2X4GB DDR3-1600 RAM....450W PSU....ASUS GeForce GTX 650 Direct Cu 1058MHZ 1GB 5.0GHZ GDDR5 2xDVI HDMI D-Sub HDCP PCI-E DX11 Video Card.... Diamond Xtreme 5.1 sound card.... LG 24X SATA DVD burner....27" LED Monitor & 26" CRT TV..... custom pressurized air cooling system.... WindowsXP Home SP3 32bit
Posted Image

#2 mjd420nova

Expert

Group: Members
Posts: 2,980
Joined: 05-August 06
Location:Fremont, California

Posted 26 November 2012 - 07:36 AM

I like the RPM range on those Silverstone units. I use ducting to get the most from each fan and the lower the speed, the lower the noise. I run four fans on the server, besides the PS fan asnd it is closed off from the case so that fan just cools the PS.

#3 waldojim

Elite

Group: Members
Posts: 15,084
Joined: 29-October 08
Location:Texas

Posted 26 November 2012 - 12:58 PM

That is sad to hear.... Scythe used to make terrific products. Hope the new fans work well for you.

"There is a cult of ignorance in the United States, and there always has been. The strain of anti-intellectualism has been a constant thread winding its way through our political and cultural life, nurtured by the false notion that democracy means that 'my ignorance is just as good as your knowledge.'" -- Isaac Asimov

Spoiler

#4 snorg

Expert

Group: Members
Posts: 2,911
Joined: 28-November 07
Location:In the wild

Posted 27 November 2012 - 06:22 PM

I found push/pull didnt make much of a difference so I will be getting only one fan.

I dont care if its noisy or not.

I just finished tearing down PC to put new video card in, had to move a hard drives out of the way to get it to fit, theres 4 hard drives, then a few days later fan dies, typical......

This post has been edited by snorg: 27 November 2012 - 06:51 PM

#5 snorg

Expert

Group: Members
Posts: 2,911
Joined: 28-November 07
Location:In the wild

Posted 29 November 2012 - 07:55 AM

CPU fan returns from the dead, like bride of frankenfan.
It works again, but I dont trust it, Im putting new fan in when it gets here.

#6 snorg

Expert

Group: Members
Posts: 2,911
Joined: 28-November 07
Location:In the wild

Posted 01 December 2012 - 09:33 PM

I put new fan in, its not like the website said.
The website showed a pic of the control knob just hanging on the end of the wire and implied it had 3 speeds.
In fact the control knob is on a plate that fits in the floppy bay on the case, and the knob is a potentiometer giving infinity variable speed.
Max RPM is rated at 2400, mine does 2500, setting the knob at 53% gave me about 2280 RPM, it cools good there and I figure it will last longer cuz its not running at full speed.
Is cools a bit better than the fan it replaced.
Its a bit noisy, high pitched whine, if you slow it down it dosnt get much quieter just a lower pitched whine, but CPU is overclocked lots so I dont care about noise.